基于数值模拟的挤压参数对AZ91镁合金管转角焊合室分流挤压焊合压力的影响规律研究

提出了一种镁合金管材转角焊合室分流挤压新工艺，该工艺可在有效延长焊合室长度和焊合时间前提下保证舌针刚度，从而保证管材尺寸精度，并且可通过转角剪切变形机制增加预焊合金属变形量和动态再结晶程度，从而有利于提高管材性能和焊缝焊合性能。利用有限元法揭示了转角焊合室分流挤压成形过程中金属的流动特征，应变分布特征和焊合室内的静水压力分布特征。结果表明，整个挤压过程无金属折叠，从而保证管材的表面质量；流经转角后预焊合金属变形量明显增加，有利于提高管材质量和焊缝质量。最后，研究揭示了坯料初始温度，挤压速度和模具转角对焊合室内静水压力的影响规律。结果表明，随着挤压速度的增加和模具转角的增大，转角焊合室内静水压力增大；随着坯料预热温度的增加，转角焊合室内静水压力呈先增大后减小的趋势。     

Influence of fluorine-containing side chain on the properties of waterborne polyurethane-urea

In order to prepare waterborne polyurethane with excellent water resistance and thermodynamic properties, a series of side chain fluorinated waterborne polyurethane-urea (FWPU-UA) was synthesized with polytetramethylene ether glycol, N-(2-methyl-1,3-propanediol-2′-)-perfluoro-1-butanesulfonyl amine (NPBA), isophorone diisocyanate, and isophoronediamine. With the increase of NPBA content, the weight loss temperature, glass transition temperature, and tensile strength of FWPU-UA were all improved. Gaussian fitting analysis of infrared data and density functional theory simulation proved that the introduction of fluorine side chains increased the interaction of hydrogen bonding in the FWPU-UA. X-ray photoelectron spectroscopy analysis indicated that the aggregation of fluorine atoms on the surface of film were caused by the migration and enrichment of fluorine side chains. Furthermore, the water resistance of polyurethane-urea film could be significantly improved by adding a small amount of NPBA, and the seven-day water absorption rate of polyurethane-urea film was reduced from 30.13% to 12.55%.     

Theoretical investigation of intrinsic point defects and the oxygen migration behavior in rare earth hafnates

In this work, the composition-dependent point defect types and formation energies of RE₂Hf₂O₇ (RE = La, Ce, Pr, Nd, Pm, Sm, Eu and Gd) as well as the oxygen diffusion behavior are systematically investigated by first-principles calculations. The possible defect reactions and dominant defect complexes under stoichiometric and non-stoichiometric conditions are revealed. It is found that O Frenkel pairs are the predominant defect in stoichiometric pyrochlore hafnates. Hf-RE cation anti-site defects, accompanied by RE vacancies and/or oxygen interstitials, are stable in the non-stoichiometric case of HfO₂ excess. On the other hand, RE-Hf anti-site defects together with oxygen vacancies and/or RE interstitials are preferable in the case of RE₂O₃ excess. The energy barriers for the migration along the V_O48f - V_O48f pathway of pyrochlore hafnates were calculated to be between 0.81 eV and 0.89 eV. Based on these results, a defect engineering strategy is proposed and the pyrochlore hafnates investigated here are predicted to exhibit potential oxygen ionic conductivity.     

Fluorescent Polyimide Films Produced with Diatomite and Mesoporous Silica as Promising High-Tech Material

Journal of Inorganic and Organometallic Polymers and Materials - Due to their excellent properties, polymides (PIs) result promising as high-performance materials in different technological fields....     

Highly oriented α-Al2O3 transparent ceramics shaped by shear force

Alumina platelets were arranged horizontally in submicron alumina particles by shear force in the flow of slurries during casting. The obtained alumina green bodies with platelets were pressureless-sintered in vacuum, producing ceramics with thoroughly oriented grains and high transmittance. The effects of sintering parameters on the densification, microstructure evolution, and orientation degree of alumina ceramics were investigated and discussed. The results showed that the densification, grain size, orientation degree, and in-line transmittance were increased with increasing sintering temperature. The enhancement of orientation degree was mainly coherent with grain growth. The grain-oriented samples exhibited a much higher in-line transmittance (at 600 nm) of 61 % than that of the grain random sample (29 %). Moreover, the transmission remained a high level in the ultraviolet range (<300 nm).     

Configurational Isomers Induced Significant Difference in All-Polymer Solar Cells

The design of polymer acceptors plays an essential role in the performance of all-polymer solar cells. Recently, the strategy of polymerized small molecules has achieved great success, but most polymers are synthesized from the mixed monomers, which seriously affects batch-to-batch reproducibility. Here, a method to separate γ-Br-IC or δ-Br-IC in gram scale and apply the strategy of monomer configurational control in which two isomeric polymeric acceptors (PBTIC-γ-2F2T and PBTIC-δ-2F2T) are produced is reported. As a comparison, PBTIC-m-2F2T from the mixed monomers is also synthesized. The γ-position based polymer (PBTIC-γ-2F2T) shows good solubility and achieves the best power conversion efficiency of 14.34% with a high open-circuit voltage of 0.95 V when blended with PM6, which is among the highest values recorded to date, while the δ-position based isomer (PBTIC-δ-2F2T) is insoluble and cannot be processed after parallel polymerization. The mixed-isomers based polymer, PBTIC-m-2F2T, shows better processing capability but has a low efficiency of 3.26%. Further investigation shows that precise control of configuration helps to improve the regularity of the polymer chain and reduce the π–π stacking distance. These results demonstrate that the configurational control affords a promising strategy to achieve high-performance polymer acceptors.     

氢能发展趋势分析及对石化企业的建议

近年来,随着全球气候变暖和对能源安全方面的考量,氢能产业在全球范围内升温,美国、日本、欧盟等发达国家及地区相继制定了氢能发展战略及规划,日本在全球氢能产业发展中表现突出,国家政策导向明确,氢能产业已成体系.我国已将氢能开发利用作为能源技术发展的重要战略方向,将"推动充电、加氢等设施建设"首次写入2019年《政府工作报告》,石化企业在国家及各级地方政府政策和规划的激励下,积极开展氢能开发利用研究.能源转型是一个漫长的过程,氢能在制取、储存运输以及利用方面还存在碳排放、安全、成本等技术障碍.建议石化企业要保持环保初心、利用自身优势,绿色开展化石能源制氢及利用.     

A new strategy to reduce edge chipping using stress wave impedance matching

To restrain edge chipping and elucidate its mechanism during machining, the initiation of edge chipping was investigated in this study from the propagation properties of stress waves in the fractured media. Three technological principles of the support for chipping suppression were proposed to reduce the intensity of reflected extension waves, namely, the wave impedance matching, the smaller residual gap and the higher viscosity of the gap filler between the workpiece and the support. As demonstrated from the experimental results, using brass support with non-solid epoxy gap filler can significantly restrain the edge chipping of pressureless sintered silicon carbide during grinding.